Script timing calculator
Word count and speaking pace in, read time, spare seconds and a word budget out.
Send a brief- You enter
- Word count, speaking pace, silent seconds, spot length
- You get
- Read time, time to spare and a word budget
- Example
- 42 words at 150 words per minute = 16.8 s
- Runs
- In your browser; nothing is sent

Calculator
A voiceover script is usually the first part of an ad that does not fit. It reads well on the page, then runs four seconds long once a narrator says it over music. This calculator turns a word count and a speaking pace into seconds, so you can see whether the script fits the spot before it goes to storyboards, and how many words each cutdown can carry.
How to use it
Fill in four values. The results update as you type.
- Words in the voiceover script. Count every spoken word, including the brand name and the call to action. Numbers count as the words a narrator says: “twenty-four” is one word, and a web address counts as each part read aloud.
- Speaking pace, in words per minute. About 150 is an unhurried read; above 180 starts to sound rushed in a commercial. If you have a recorded read from the voice you plan to cast, count its words and time it.
- Planned seconds without voice. Music-only moments, the end card, and pauses that let a visual beat land.
- Spot length. The length of the version you are writing for, in seconds.
How the calculation works
- Read time = words / pace x 60.
- With the planned silence = read time + seconds without voice.
- Time to spare = spot length minus that total. If the total is longer than the spot, the calculator shows how many seconds the script is over.
- Most words that fit = (spot length minus seconds without voice) x pace / 60, rounded down.
- Words per second = pace / 60.
- The rough word budget for 6, 15 and 60 seconds uses the same formula with the silence capped at one fifth of each length, so a 6-second cutdown is not handed the full silence planned for the 30. Results are rounded down.
The worked example
Example (fictional). The Orlenna Ridge Bottle hero spot is 30 seconds. Its voiceover has 42 words: “Six a.m. on the ridge. Coffee poured at the trailhead is still hot at the top. Two steel walls, a vacuum between them, and a copper layer that keeps heat where you put it. Orlenna Ridge Bottle. Twelve hours hot. Twenty-four cold.”
At 150 words per minute, 42 / 150 x 60 = 16.8 seconds of read time. The cut plans 6 seconds of music-only moments, so the total is 22.8 seconds, leaving 7.2 seconds to spare. The pace is 2.50 words per second, and the most words that fit this spot are (30 minus 6) x 2.5 = 60 words. The rough word budget is 12 words for 6 seconds, 30 words for 15 seconds and 135 words for 60 seconds.
Reading the result
Time to spare is room for the picture. In the example, 7.2 seconds leaves room to hold a shot without words or to keep the end card on screen longer. A script with no spare time usually means a rushed read or an edit cut to the voice rather than to the images.
Over the spot length means the script does not fit. Cut words first. Slow the edit only if the visuals allow it, or move a line onto the screen as type, which is often how a claim such as “twelve hours hot” survives in shorter versions.
The word budget for cutdowns shows that a long script rarely shrinks by trimming alone. A 6-second version at this pace carries about 12 words, so it needs its own line, written and approved with the hero script. “Orlenna Ridge Bottle. Twelve hours hot. Twenty-four cold.” is 9 words and would fit the fictional example’s 6-second cut.
Limits
- Pace depends on the voice, the language, the music and the brand. The calculator uses one average pace; a real read speeds up and slows down.
- Each language version has its own word count. Time the translated script separately rather than assuming it matches the English.
- Words shown on screen as type need reading time too, and the calculator does not count them.
- Read the script aloud with a stopwatch before it is approved, and again once the animatic is cut to a scratch voiceover.
Related decisions
Script timing feeds the animatic, where the read is cut against the boards while changes are still cheap; see creative development and 2D animation, where kinetic type often carries lines the voice cannot. The number of lengths you need comes from the versioning matrix calculator, and the frame and timecode calculator converts the timings into frames for the edit. The creative brief worksheet has a line for the one message the script must carry.
When the script and the lengths are settled, send a brief with both, and the production plan will time every version against them.